 |
 |
|
||
 |
||||
Printer Specifications
Mechanical
|
Printing method:
|
24-pin impact dot matrix
|
|
|
Printing speed:
(Normal) |
High speed draft
|
440 cps at 10 cpi
529 cps at 12 cpi |
|
Draft
|
330 cps at 10 cpi
396 cps at 12 cpi 496 cps at 15 cpi |
|
|
Draft condensed
|
283 cps at 17 cpi
330 cps at 20 cpi |
|
|
LQ
|
110 cps at 10 cpi
132 cps at 12 cpi 165 cps at 15 cpi |
|
|
LQ condensed
|
188 cps at 17 cpi
220 cps at 20 cpi |
|
|
Printing speed:
(Copy) |
High speed draft
|
347 cps at 10 cpi
416 cps at 12 cpi |
|
Draft
|
260 cps at 10 cpi
312 cps at 12 cpi 390 cps at 15 cpi |
|
|
Draft condensed
|
223 cps at 17 cpi
260 cps at 20 cpi |
|
|
LQ
|
86 cps at 10 cpi
104 cps at 12 cpi 130 cps at 15 cpi |
|
|
LQ condensed
|
148 cps at 17 cpi
173 cps at 20 cpi |
|
|
Printing direction:
|
Bidirectional logic seeking for text and graphics printing. Unidirectional text or graphics printing can be selected using software commands.
|
|
|
Line spacing:
|
1/6-inch or programmable in 1/360-inch increments
|
|
|
Printable columns:
|
106 columns (at 10 cpi)
|
|
|
Resolution:
|
360 × 360 dpi maximum
|
|
|
Feeding method:
|
Friction feed (front, rear paper entry)
Push tractor feed (rear paper entry) |
|
|
Feeder:
|
Rear push tractor
Roll paper holder (Optional) |
|
|
Paper feed speed:
|
Normal mode:
|
|
|
Intermittent
|
64 mm second/line at 1/6-inch line spacing
|
|
|
Continuous feed
|
127 mm/second
(5.0 inches/second) |
|
|
Copy mode:
|
||
|
Intermittent
|
71 mm second/line at 1/6-inch line spacing
|
|
|
Continuous feed
|
92 mm/second
(3.6 inches/second) |
|
|
Reliability:
|
Total print volume
|
40 million lines
(except print head) MTBF 20,000 POH (25% duty) |
|
Print head life
|
400 million strokes per wire
|
|
|
Dimensions and weight:
|
Height
|
210 mm (8.26 inches)
|
|
Width
|
480 mm (18.90 inches)
|
|
|
Depth
|
370 mm (14.57 inches)
(excluding the paper guide, paper release lever, etc.) |
|
|
Weight
|
approx. 6.8 kg (8.7 lb)
|
|
|
Ribbon:
|
Black ribbon Cartridge
|
S015610/S015628
|
|
Ribbon life
|
10 million characters
(LQ, 10 cpi, 48 dots/ character) |
|
|
Acoustic noise:
|
Approx. 57 db (A) (ISO 7779 pattern)
|
|
Electronic
|
Interfaces:
|
One standard bidirectional, 8-bit, parallel interface with IEEE-1284 nibble mode support, and one USB2.0 (Full Speed) interface.
|
|
Buffer:
|
128KB
|
|
Built-in fonts:
|
Bitmap fonts:
EPSON Draft 10 CPI, 12 CPI, 15 CPI
EPSON Roman 10 CPI, 12 CPI, 15 CPI, Proportional EPSON Sans Serif 10 CPI, 12 CPI, 15 CPI, Proportional EPSON Courier 10 CPI, 12 CPI, 15 CPI EPSON Prestige 10 CPI, 12 CPI EPSON Script 10 CPI EPSON OCR-B 10 CPI EPSON Orator 10 CPI EPSON Orator-S 10 CPI EPSON Script C Proportional Scalable fonts:
EPSON Roman 10.5 pt., 8 pt. - 32 pt. (every 2 pt.)
EPSON Sans Serif 10.5 pt., 8 pt. - 32 pt. (every 2 pt.) EPSON Roman T 10.5 pt., 8 pt. - 32 pt. (every 2 pt.) EPSON Sans Serif H 10.5 pt., 8 pt. - 32 pt. (every 2 pt.) Bar code fonts:
EAN-13, EAN-8, Interleaved 2 of 5, UPC-A, UPC-E, Code 39, Code 128, POSTNET
|
|
Character tables:
|
ASCII
Italic table PC 437 (US, Standard Europe) PC 850 (Multilingual) PC 860 (Portuguese) PC 860 (Icelandic) PC 865 (Nordic) PC 863 (French-Canadian) PC 858 (Multilingual Euro) Abicomp BRASCII Roman 8 ISO Latin ISO 8859-15 PC 437 Greek PC 852 (East Europe) PC 853 (Turkish) PC 855 (Cyrillic) PC 857 (Turkish) PC 866 (Russian) PC 869 (Greek) MAZOWIA (Poland) Code MJK (CSFR) ISO 8859-7 (Latin/Greek) ISO Latin 1T (Turkish) Bulgaria (Bulgarian) Estonia (Estonia) PC 744 (LST 1283:1993) ISO 8859-2 PC 866 LAT. (Latvian) PC 866 UKR (Ukrania) PC 437 Slovenia PC MC PC 1250 PC 1251 PC 864 (Arabic) PC APTEC (Arabic) PC 708 (Arabic) PC 720 (Arabic) PCAR 864 (Arabic) |
|
Character sets:
|
14 international character sets and one legal character set:
USA, France, Germany, UK, Denmark I, Sweden, Italy, Spain I Japan, Norway, Denmark II, Spain II Latin America, Korea, Legal Letter 7 sets can be selected only with the ESC R command. |
Electrical
|
220 to 240 V
|
|
|
Input voltage range
|
AC 198 to 264 V
|
|
Rated frequency range
|
50 to 60 Hz
|
|
Input frequency range
|
49.5 to 60.5 Hz
|
|
Rated current
|
0.6 A (maximum 1.3 A depending on the character type)
|
|
Power consumption
|
Approx. 37.5 W (ISO/IEC 10561 letter pattern)
Approx. 2.4 W in sleep mode*
Approx. 0 W in power off mode
|
* When 5 minutes pass in the following condition, the printer enters sleep mode.
- not pause.
- not error.
- not pause.
- not error.
Note:|
Check the label on the back of the printer for the voltage of your printer.
|
Environmental
|
Temperature
(without condensation) |
Humidity
(without condensation) |
|
|
Operation
|
5 to 35 ˚C (41 to 95 ˚F)
|
10 to 80% RH
|
|
Storage
|
-30 to 60 ˚C (-22 to 140 ˚F)
|
0 to 85% RH
|
Paper
Note:|
Use recycled paper, envelopes, labels and single-sheet multipart forms only under normal temperature and humidity conditions, as follows:
Temperature: 15 to 25 ˚C (59 to 77 ˚F) Humidity: 30 to 60% RH Do not load paper that has been folded or is damaged, wrinkled, or curled.
|
Single sheets (standard): paper guide entry
|
Width
|
90 to 304.8 mm (3.5 to 12 inches)
|
|
Length
|
70 to 420 mm (2.8 to 16.5 inches)
|
|
Thickness
|
0.065 to 0.19 mm (0.0025 to 0.0074 inch)
|
|
Weight
|
52 to 157 g/m² (14 to 42 lb)
|
Single-sheet multipart forms: paper guide entry
See also Multipart forms for detailed information on the specification for single-sheet multipart forms.
|
Width
|
90 to 304.8 mm (3.5 to 12 inches)
|
|
Length
|
70 to 420 mm (2.8 to 16.5 inches)
|
|
Copies
|
1 original + up to 6 copies
|
|
Thickness
|
0.12 to 0.49 mm (0.0047 to 0.019 inch)
|
|
Weight
|
40 to 58 g/m² (10 to 15 lb)
|
|
Binding
|
Line-glued at the top or one side of form
|
|
Quality
|
Carbonless or carbon-backed multipart forms with a line of glue at the top or the side of the formMultipart forms that are joined together along the left and right edges by crimping or spot-gluing*
|
* When using 4 inches or wider but less than 9.4 inches wide multipart forms joined by crimping (multipart forms with cut-paper tab binding), set the Multipart forms with cut-paper tab binding in the default-setting mode to on.
Card: paper guide entry
|
Width
|
100 to 200 mm (3.9 to 7.8 inches)
|
|
Length
|
100 to 200 mm (3.9 to 7.8 inches)
|
|
Thickness
|
0.22 mm (0.0087 inch)
|
|
Weight
|
192 g/m² (51 lb)
|
Envelopes: paper guide entry
|
Size
|
No. 6: 165 × 92 mm (6.5 × 3.6 inches)
No. 10: 241 × 105 mm (9.5 × 4.1 inches) |
|
Thickness
|
0.16 to 0.52 mm (0.0063 to 0.0205 inch)
|
|
Weight
|
45 to 90 g/m² (12 to 24 lb)
|
Continuous paper: rear entry
|
Width
|
101.6 to 304.8 mm (4.0 to 12.0 inches)
|
|
Length (one page)
|
76.2 to 558.8 mm (3.0 to 22.0 inches)
|
|
Copies
|
1 original + up to 6 copies
|
|
Thickness
|
0.065 to 0.49 mm (0.0025 to 0.019 inch)
|
|
Weight
(not multipart) |
52 to 128 g/m² (14 to 34 lb)
|
|
Weight
(one sheet of multipart) |
40 to 58 g/m² (10 to 15 lb)
|
|
Quality
|
Plain paper, Reclaimed paper
Carbonless multi part paper
Not break, without wrinkle, without tear, without turn over
|
|
Binding
|
Spot glued or crimp bound on both sides
|
Continuous paper multipart form: rear entry
See also “Multipart forms” for detailed information on the specification for single-sheet multipart forms.
Labels (Continuous paper): rear entry
|
Label size
|
23.8 × 63.5 mm (15/16 × 2.5 inches) minimum
2.5 mm (0.1 inch) corner radius, minimum |
|
Base sheet width
|
101.6 to 304.8 mm (4.0 to 12.0 inches)
|
|
Base sheet length
|
101.6 to 558.8 mm (4.0 to 22.0 inches)
|
|
Base sheet thickness
|
0.07 to 0.09 mm (0.0028 to 0.0035 inch)
|
|
Total thickness
|
0.16 to 0.19 mm (0.0063 to 0.0075 inch)
|
|
Label weight
|
64 g/m² (17 lb)
|
Labels (Cut sheet): rear entry
|
Label size
|
23.8 × 63.5 mm (15/16 × 2.5 inches) minimum
2.5 mm (0.1 inch) corner radius, minimum |
|
Base sheet width
|
100 to 210 mm (3.9 to 8.3 inches)
|
|
Base sheet length
(one page) |
100 to 297 mm (3.9 to 11.7 inches)
|
|
Base sheet thickness
|
0.07 to 0.09 mm (0.0028 to 0.0035 inch)
|
|
Total thickness
|
0.16 to 0.19 mm (0.0063 to 0.0075 inch)
|
|
Label weight
|
64 g/m² (17 lb)
|
Roll paper: rear entry with optional roll paper holder
|
Width
|
216 mm (8.5 inches)
|
|
Thickness
|
0.07 to 0.09 mm (0.0028 to 0.0035 inch)
|
|
Weight
|
52 to 82 g/m² (14 to 22 lb)
|
Multipart forms
The specifications for the dimensions of multipart forms are the same as those for single sheets and continuous paper. See Paper for detailed information.
The form sheets of continuous multipart forms should be securely joined together along the left and right edges by crimping or, spot-gluing. For the best printing quality, use multipart forms joined with spot-gluing.
|
spot-gluing
|
|
 |
|
|
crimping
|
|
 |
|
|
spot-gluing and crimping on each side
|
|
 |
|
|
1. 1 inch or less
2. 3 inches or less
3. printing side
| |
Note:|
When using 4 inches or wider but less than 9.4 inches wide multipart forms joined by crimping (multipart forms with cut-paper tab binding), set the Multipart forms with cut-paper tab binding in the default-setting mode to on.
|
Caution:|
Never use continuous multipart forms that are joined with metal staples or bar-gluing.
|
 |
 |
|
1. bar-gluing
2. metal stapling
|
|
The thickness of the folded part when extended should be 1 mm or less.
 |
|
* 1 mm or less
|
The binding area should be flat and have no creases.
The sprocket holes should be a circle or a notched circle.
The sprocket holes of all sheets in the form should be aligned properly.
The binding position should be outside the recommended printable area. See Recommended printable area for more information.
Recommended printable area
Note:|
For best results, print within the recommended printable area. The printer may not print outside this area.
|
Single sheets and envelopes:
 |
 |
|
A
|
The minimum top margin is 4.2 mm (0.17 inch).
|
|
B
|
The minimum left and right margins are 3.0 mm (0.12 inch) each.
For single sheets the maximum paper width is 304.8 mm (12.0 inches) and the maximum printable width is 269.24 mm (10.6 inches).
For single sheets wider than 275.24 mm (10.8 inches), the side margins increase proportionally to match the width of the paper.
|
|
C
|
The minimum bottom margin is 4.2 mm (0.17 inch).
|
Continuous paper:
|
A
|
The minimum top and bottom margins above and below the perforation are 4.2 mm (0.17 inch) each.
|
|
B
|
The minimum left and right margins are 13 mm (0.51 inch) each.
The maximum paper width is 304.8 mm (12.0 inches) and the maximum printable width is 269.24 mm (10.6 inches).
For continuous paper wider than 279.4 mm (11.0 inches), the side margins increase proportionally to match the width of the paper.
|
Label:
|
A
|
3 mm (0.118 inch) or more
|
|
B
|
18 mm (0.709 inch) or more
|
|
C
|
23 mm (0.906 inch) or more
|
Label (continuous form):
|
A
|
3 mm (0.118 inch) or more
|
|
B
|
1.2 mm (0.0472 inch) or more
|
|
C
|
6.35 mm (0.25 inch) or more
|
Roll paper:
|
A
|
The minimum top margin is 4.2 mm (0.17 inch).
|
|
B
|
The minimum left margin is 3.0 mm (0.12 inch).
The minimum right margin is 3.0 mm (0.12 inch).
The maximum printable width is 269.24 mm (10.6 inches).
|
Paper alignment
Printing starts at “0” on the scale. The unprintable area is to the left of the “0.”
