|
|
How to / SelecType Settings
When to use SelecType
How to make the settings
SelecType menu table
In general, use SelecType only for settings you cannot make in your software or printer driver, including the following:
Keep in mind the following when using SelecType settings:
Use the buttons on the printer's display panel to enter SelecType mode. SelecType settings appear on the display panel.
1. Menu
2. Item
3. Value
4. Enter
Note: |
You can directly access certain menu items using the OneTouch modes. For more information, see Using the OneTouch Modes. |
Press the SelecType button several times until the light above SelecType (ALT) comes on. |
Press the Menu button to enter SelecType mode. |
Use the Menu, Item, and Value buttons to display settings, like this: |
To display menus, press Menu.
To display items in a menu, press Item.
To display values for an item, press Value.
An asterisk () appears beside the currently activated value.
Press ALT in combination with each button to display menus, items, or values in reverse order.
See SelecType menu table for a list of SelecType menus and items.
To activate a new setting, press Enter. An asterisk () appears beside the setting. |
To exit the SelecType mode, press On Line or SelecType. |
See SelecType Settings for a detailed description of SelecType settings.
The following table shows the order in which SelecType menus and menu items appear on the display panel.
Press the Menu button to display the next menu. Press the Alt and Menu buttons to display the previous menu.
Menu |
Items |
Test Menu |
Status Sheet, PS3 Status Sheet*, Network Status Sheet, Aux Status Sheet*, LJ4 Font Sample, ESCP2 Font Sample, FX Font Sample, |
Emulation Menu |
Parallel, Network, AUX* |
Printing Menu |
Paper Source, Page Size, Wide A4, Orientation, Out Bin, Copies, Manual Feed, Resolution, Skip Blank Page, Auto Eject Page, Duplex*, Binding*, Start Page*, Offset Stacking, Staple, Staple Position |
Tray Menu |
MP Mode, MP Tray Size, ENV Tray Size*, MP Type, LC1 Type, LC2 Type, LC3 Type*, LC4 Type*, LC5 Type* |
Config Menu |
RITech, Toner Save, Density, Top Offset, Left Offset, T Offset B*, L Offset B*, Size Ignore, Auto Cont, Page Protect, Image Optimum |
Setup Menu |
Interface, Time Out, Standby, Lang,Toner, |
Parallel Menu |
Speed, Bi-D, Buffer Size |
Network Menu |
Network Config, Get IPAddress*, IP Byte1*, IP Byte2*, IP Byte3*, IP Byte4*, SM Byte1*, SM Byte2*, SM Byte3*, SM Byte4*, GW Byte1*, GW Byte2*, GW Byte3*, GW Byte4*, Buffer Size |
AUX Menu* |
AUX Config*, Get IPAddress*, IP Byte1*, IP Byte2*, IP Byte3*, IP Byte4*, SM Byte1*, SM Byte2*, SM Byte3*, SM Byte4*, GW Byte1*, GW Byte2*, GW Byte3*, GW Byte4*, NetWare*, AppleTalk*, NetBEUI*, AUX Init*, Buffer Size |
LJ4 Menu |
Font Source, Font Number, Pitch, Height, SymSet, Form, Source SymSet*, Dest SymSet*, |
GL2 Menu |
GLMode, Scale, Origin, Pen, End, Join, Pen0, Pen1, Pen2 to Pen6 |
PS3 Menu* |
Error Sheet |
ESCP2 Menu |
Font, Pitch, Condensed, T.Margin, Text, CG Table, Country, Auto CR, Auto LF, Bit Image, ZeroChar |
FX Menu |
Font, Pitch, Condensed, T.Margin, Text, CG Table, Country, Auto CR, Auto LF, Bit Image, ZeroChar |
I239X Menu |
Font, Pitch, Code Page, T.Margin, Text, Auto CR, Auto LF, Alt. Graphics, Bit Image, ZeroChar, CharacterSet |
* These Items appear only when the corresponding option is installed. |
Previous |
Next |
Version 1.00E, Copyright © 2002, SEIKO EPSON CORPORATION |