Reference Guide
|
|
Product Information
Safety Instructions
Important Safety Instructions
A Few Precautions
Important Safety Instructions
Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer.
-
Do not block or cover the openings in the printer's cabinet.
-
Do not insert objects through the slots. Take care not to spill liquid on the printer.
-
Use only the type of power source indicated on the printer's label.
-
Connect all equipment to properly grounded power outlets. Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off.
-
Avoid electrical outlets controlled by wall switches or automatic timers.
-
Keep the entire computer system away from potential sources of electromagnetic interference, such as loudspeakers or the base units of cordless telephones.
-
Do not use a damaged or frayed power cord.
-
If you use an extension cord with the printer, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord's ampere rating. Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet's ampere rating.
-
Do not attempt to service the printer yourself.
-
Unplug the printer and refer servicing to qualified service personnel under the following conditions:
The power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the cabinet damaged; the printer does not operate normally or exhibits a distinct change in performance.
-
The interface connectors (including Type B interface card) and the connector for optional Auto Take-up Reel Unit are Non-LPS (non-limited power source).
-
If you plan to use the printer in Germany, observe the following:
To provide adequate short-circuit protection and over-current protection for this printer, the building installation must be protected by a 10 or 16 amp circuit breaker.
[Top]
A Few Precautions
When choosing a place for the printer
-
Place the printer on a flat, stable surface that is larger than the printer. The printer will not operate properly if it is tilted or at an angle.
-
Avoid places subject to rapid changes in temperature and humidity. Also keep it away from direct sunlight, strong light, or heat sources.
-
Avoid places subject to shocks and vibrations.
-
Keep the printer away from the dusty areas.
-
Place the printer near a wall outlet where the plug can be easily unplugged.
ENERGY STAR® Compliance
As an International ENERGY STAR® Partner, EPSON has determined that this product meets the International ENERGY STAR® Program guidelines for energy efficiency.
The International ENERGY STAR® Office Equipment Program is a voluntary partnership with the computer and office equipment industry to promote the introduction of energy-efficient personal computers, monitors, printers, fax machines, copiers, and scanners, in an effort to reduce air pollution caused by power generation.
When using the printer
-
Do not put your hand inside the printer or touch the ink cartridges during printing.
-
Do not move the print heads by hand; otherwise you may damage the printer.
-
Always turn the printer off using the Power button on the control panel. When this button is pressed, the Operate light flashes briefly then goes off. Do not unplug the printer or turn off the power to the outlet until the Operate light stops flashing.
-
Before transporting the printer, make sure the print heads are in the home (far right) position.
When handling the ink cartridges
-
Keep ink cartridges out of the reach of children and do not drink.
-
If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water.
-
If you use EPSON UltraChrome type ink cartridges, shake the ink cartridge gently before installing it for best results.
|
Caution
|
|
Do not shake cartridges that have been installed previously.
|
-
Do not use an ink cartridge beyond the date printed on the cartridge carton.
-
If you use EPSON UltraChrome type ink cartridges, use up the ink cartridge within six months of installation for best results.
-
Do not dismantle the ink cartridges or try to refill them. This could damage the print heads.
-
Store ink cartridges in a cool, dark place.
-
After bringing an ink cartridge inside from a cold storage site, allow it to warm up at room temperature for at least three hours before using it.
-
Do not touch the green IC chip on the side of the cartridge. This may affect normal operation and printing.
-
In this ink cartridge, the IC chip retains a variety of cartridge related-information, such as the amount of ink remaining, so that a cartridge may be removed and reinserted freely.
-
If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust, and store it in the same environment as the printer. Note that there is a valve in the ink supply port, making covers or plugs unnecessary, but care is needed to prevent the ink from staining items that the cartridge touches. Do not touch the ink supply port or surrounding area.
[Top]
Version 1.10E, Copyright © 2002, SEIKO EPSON CORPORATION |