Reference Guide

Index Search Glossary Contents Help

Troubleshooting / Scanning Problems

Scanned Image Problems

The edges of a document are not scanned
You cannot scan a document or you only get a few dots for the scanned image
A line of dots is always missing from the scanned image
A line of dots always appears in the scanned image
Straight lines in the image come out jagged
Scanned image by using the buttons on the control panel is missing
The image is distorted or blurred
Colors are patchy or distorted at the edges of the image
The image is dark
Moiré (cross-hatch) patterns appear in the scanned image
Poor character recognition during OCR scanning
The image is larger or smaller than the original
Scanned images cannot be printed or come out garbled when printed
Colors differ from the original
Images cannot be located properly in the Thumbnail Preview

The edges of a document are not scanned

Try one or more of these solutions:

• Place the document away from the edges of the document table to avoid any unwanted image cropping.

• The area with a maximum width of 2.5 mm from the horizontal and vertical edges is not scanned.

1,2. Maximum unreadable area of 2.5 mm

[Top]

You cannot scan a document or you only get a few dots for the scanned image

Try one or more of the following solutions.

• Make sure the document is placed on the document table of this product, with the side to be scanned facing down.

• When scanning with the Black&White setting in the Home Mode or the Professional Mode, change the Threshold setting.

[Top]

A line of dots is always missing from the scanned image

If a line is missing on both your screen image and printout, this indicates the scanner sensor is malfunctioning. Contact you dealer.

[Top]

A line of dots always appears in the scanned image

If this happens on both your screen image and printout, this indicates that the document table may be dusty or scratched. Clean the document table. If you still have the problem, contact your dealer.

[Top]

Straight lines in the image come out jagged

Make sure the document orientation is perfectly straight on the document table. Align the vertical and horizontal lines with the scales at the top and side of the document table.

[Top]

Scanned image by using the buttons on the control panel is missing

Make sure desired application is assigned to the buttons on the control panel.

[Top]

The image is distorted or blurred

Try one or more of the following solutions.

• Make sure the document is flat against the document table.

Caution:

Do not place heavy objects on the document table.

• Make sure you do not accidentally move the document while scanning.

• Make sure this product is on a flat, stable surface.

• Change the Display Gamma setting of the scanned image to fit to the gamma setting of your output device in the Configuration dialog box.

• Select Unsharp Mask Filter in the Professional Mode main window. If moiré patterns appear in the image, see Moiré (cross-hatch) patterns appear in the scanned image for more information.

• Select Color Control and also check Continuous auto exposure in the Configuration dialog box, or adjust the Exposure setting using the Auto Exposure button in the Professional Mode main window.

• Change the Resolution setting for your document.

• If this happens on part of the image, make sure the document is uniformly flat against the document table. A document that is wrinkled or warped may not be scanned well.

[Top]

Colors are patchy or distorted at the edges of the image

Try one or more of the following solutions.

• A document that is very thick or warped at the edges can cause discoloration. Cover the edges of the document with paper to block the external light.

• Make sure the document is flat against the document table.

Caution:

Do not place heavy objects on the document table.

• Adjust your software's Gamma setting using the Histogram Adjustment dialog box in the Professional Mode.

[Top]

The image is dark

Try one or more of the following solutions.

• Check your software's Brightness setting using the Image Adjustment dialog box in the Home Mode, or the Histogram Adjustment dialog box and the Image Adjustment dialog box in the Professional Mode.

• Check the brightness and contrast settings of your computer display.

• Select Color Control and also select Continuous auto exposure in the Configuration dialog box, or adjust the Exposure setting using the Auto Exposure button in the Professional Mode main window.

• Change the Display Gamma setting of the scanned image to fit to the gamma setting of your output device in the Configuration dialog box.

• Change the Destination setting in the Home Mode or the Professional Mode main window.

• In the Home Mode, select Screen/Web as Destination. Selecting a printer may cause on-screen colors to be different from the colors of the original; however, the colors will be reproduced correctly when the image is printed.

[Top]

Moiré (cross-hatch) patterns appear in the scanned image

A moiré is a cross-hatch pattern that appears on the scanned images when you scan printed materials. It is a result of interference that occurs due to the difference between the pitches of the scanning and the halftone screens.

Try one or more of the following solutions.

• Select the Descreening Filter check box in the Home Mode or the Professional Mode main window.

• In the Professional Mode, set the Screen Ruling of the Descreening Filter setting to an appropriate setting for your document.

• Clear Unsharp Mask Filter in the Professional Mode main window.

• Place a transparent sheet, such as an overhead projector sheet, between the document and the document table.

• Reposition the document slightly.

• Make the image size slightly smaller.

[Top]

Poor character recognition during OCR scanning

Try one or more of the following solutions.

• Make sure the document orientation is perfectly aligned along the document table. Align the vertical and horizontal lines with the scales at the top and side of the document.

• Select Black&White as the Image Type setting. In the Professional Mode, select None for the B&W Option setting. Then try adjusting the Threshold setting. See Scan Documents to Convert to Text Data (OCR) for more information.

[Top]

The image is larger or smaller than the original

Try one or more of the following solutions.

• The image size and resolution settings of your software determine the size of the printed image. Do not use the size of the monitor image to judge the printed size.

• Change the Target Size setting of the Destination setting in the Home Mode or the Professional Mode main window.

[Top]

Scanned images cannot be printed or come out garbled when printed

Try one or more of the following solutions.

• Make sure this product is properly connected to the computer, correctly set up, and maintained.

• Check that your software is properly installed and set up for your printer. See your Setup Guide.

[Top]

Colors differ from the original

Try one or more of these solutions:

• Change the Image Type setting. See online help to make sure your settings are correct.

• Change the image settings of your scanner software, especially the data format (bits, pixel, color), gamma correction, and color correction. Try different combinations of these settings.

• Change the Display Gamma setting of the scanned image to fit to the gamma setting of your output device in the Configuration dialog box.

• Select Color Control and select Continuous auto exposure in the Configuration dialog box. Or, adjust the Exposure setting by using the Auto Exposure button in the Professional Mode main window.

• Check the color matching and color management capabilities of your computer, display adapter, and software. Some computers can change the color palette to adjust the colors on your screen. See your software and hardware manuals for details.

• Use the color management system for your computer: ICM for Windows, or ColorSync for Macintosh. For Windows, add a color profile that matches your monitor.

• Exact color matching is very difficult. Check your software and monitor documentation for information on color matching and calibration.

• Printed colors do not exactly match the colors on your monitor, since printers and monitors use different color systems: monitors use RGB (red, green, and blue), while printers typically use CMYK (cyan, magenta, yellow, and black).

[Top]

Images cannot be located properly in the Thumbnail Preview

Try one or more of the following solutions.

• In the Preview window, create marquees on the area you want to scan, and then scan.

• In the Configuration dialog box, adjust the thumbnail cropping area using the Thumbnail Cropping Area slider.

[Top]

Previous

Next