Reference Guide
|
|
Product Information
Safety Instructins
Warnings, Cautions, and Notes
Hot Parts caution symbol
Important safety instructions
For United Kingdom Users
Safety information
Warnings, Cautions, and Notes
This guide uses the following conventions:
|
Warnings
|
|
must be followed carefully to avoid bodily injury.
|
|
|
Cautions
|
|
must be observed to avoid damage to your equipment.
|
|
|
Notes
|
|
contain important information and useful tips on the operation of your printer.
|
|
[Top]
Hot Parts caution symbol
|
The symbol on the print head indicates that this part may be hot. Never touch the print head just after the printer has been used. Let the print head cool for a few minutes before touching it.
|
[Top]
Important safety instructions
Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the printer.
-
Do not place the printer on an unstable surface or near a radiator or heat source.
-
Place the printer on a flat surface. The printer will not operate properly if it is tilted or at an angle.
-
Do not block or cover the openings in the printer's cabinet. Do not insert objects through the slots.
-
Use only the type of power source indicated on the printer's label.
-
Connect all equipment to properly grounded power
outlets. Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch
on and off.
-
Do not use a damaged or frayed power cord.
-
If you use an extension cord with the printer, make sure
the total ampere rating of all devices plugged into the extension cord does not exceed the cord's ampere rating. Also, make sure the total of all devices plugged into the wall outlet does not exceed the wall outlet's ampere rating.
-
Unplug the printer before cleaning, and clean it with a damp cloth only.
-
Do not spill liquid on the printer.
-
Except as specifically explained in this guide, do not attempt to service the printer yourself.
-
Unplug the printer and refer servicing to qualified service personnel under the following conditions:
If the power cord or plug is damaged; if liquid has entered
the printer; if the printer has been dropped or the cabinet damaged; or if the printer does not operate normally or exhibits a distinct change in performance. Adjust only those controls that are covered by the operating instructions.
-
If you plan to use the printer in Germany, observe the following:
To provide adequate short-circuit protection and over-current protection for this printer, the building installation must be protected by a 16 Amp circuit breaker.
| |
Note for German-speaking users:
|
| |
Bei Anschluß des Druckers an die Stromversorgung muß sichergestellt werden, daß die Gebäudeinstallation mit einem 16 A-Überstromschalter abgesichert ist.
|
|
ENERGY STAR Compliance
As an ENERGY STAR Partner, EPSON has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
The International ENERGY STAR Office Equipment program
is a voluntary partnership with the computer and office
equipment industry to promote the introduction of
energy-efficient personal computers, monitors, printers, fax machines, copiers, and scanners in an effort to reduce air pollution caused by power generation.
[Top]
For United Kingdom Users
Use of options
Epson (UK) Limited shall not be liable against any damages
or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Epson (UK) Limited.
[Top]
Safety information
|
Warning:
|
|
This appliance must be earthed. Refer to rating plate for voltage and check that the appliance voltage corresponds to the supply voltage.
|
|
Important:
The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and yellow Earth
Blue Neutral
Brown Live
If you have to fit a plug:
As the colours of the mains lead of this appliance may not match coloured markings used to identify the terminals in a plug, please proceed as follows:
The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or the Earth symbol ().
The blue wire must be connected to the terminal in the plug marked with the letter N.
The brown wire must be connected to the terminal in the plug marked with the letter L.
If damage occurs to the plug, replace the cord set or consult a qualified electrician.
Replace fuses only with a fuse of the correct size and rating.
[Top]
Version 1.00E, Copyright © 2002, SEIKO EPSON CORPORATION |