|
|
Network Software / EpsonNet WebAssist
Input
Emulation
Interface
This section gives the printer information. Using EpsonNet WebAssist, you can make some of the same printer settings that you can set using the printer's control panel. See the Reference Guide for more information on each item.
Note: |
|
Items |
Explanations |
MP Mode |
Select the priority order of paper feeding from MP Tray. |
MP Tray Paper Size |
Select the paper size for MP Tray. |
LC Paper Size |
Displays the currently loaded paper size in the lower paper cassette if the optional Large Capacity Paper Unit is installed |
MP Tray Paper Type |
Select the paper type for MP Tray. |
LC Paper Type |
Select the paper type for the lower paper cassette only if the optional Large Capacity Paper Unit is installed. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Menu Selection |
Select Setup. |
Interface Time Out |
Enter the length of the printer waits when it is on line and no new data is received. When this time is up, the printer searches for new print data on other channels. |
Language |
Select the displayed language. |
Panel Lock |
Select locking of the printer's control panel. If you select on, the printer's control panel is locked. |
Toner Out |
Select whether to continue printing when the toner is out. |
LCD Contrast |
Adjust the contrast of the LCD display. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Menu Selection |
Select Printing. |
Paper Source |
Select the paper source. |
Paper Size |
Select the paper size for printing. |
Wide A4 |
Select whether the printer accepts wide A4 paper for printing. |
Orientation |
Select whether the page is printed in portrait or landscape orientation. |
Copies |
Enter the number of copies to be printed. |
Manual Feed |
This item selects manual feed mode. |
Resolution |
Select the resolution. |
Skip Blank Page |
Select whether to skip a blank page. |
Auto Eject Page |
Select whether to eject pages automatically. |
Duplex |
Select whether to print on both sides of paper. This setting is available only when the Duplex Unit is installed. |
Binding |
Specify the binding direction of the printout. This setting is available only when the Duplex Unit is installed. |
Start Page |
Specify whether printing starts from the front or back side of the page. This setting is available only when the Duplex Unit is installed. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Menu Selection |
Select Configuration. |
RITech |
Select whether to adjust the RITech setting. RIT produces smoother and crisper lines, text, and graphics. |
Toner Save |
Select whether to save toner. When on, the printer consumes less toner but print quality is reduced. |
Top Offset |
Enter a value to adjust the printing start position from the top on the paper. |
Left Offset |
Enter a value to adjust the printing start position from the left on the paper. |
Top Offset B |
Enter a value to adjust the vertical printing position on the back side when printing on both sides. Available only when the Duplex Unit is installed. |
Left Offset B |
Enter a value to adjust the horizontal printing position on the back side when printing on both sides. Available only when the Duplex Unit is installed. |
Size Ignore |
Select whether a paper size error is ignored. |
Auto Continue |
Select whether to permit the printer to automatically continue printing after a certain period of time when one of the following error occurs: paper set, print overrun, or insufficient memory error. |
Page Protect |
Select whether to allocate additional printer memory for printing data, as opposed to receiving it. |
Image Optimum |
Reduces the amount of graphics data when the data reaches the memory limit, allowing complex documents to be printed. |
Paper Type |
Select the paper type. |
Paper Side |
When you print on thick or extraThk paper or envelope, select the paper side to be printed. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Menu Selection |
Select Support. |
Sleep Mode |
Select whether to save power, by reducing power to the fixing heater when the printer receives no data for a certain period of time. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Emulation |
Select PS3. This menu appears only when PS3 is installed. |
Error Sheets |
Select whether to print an error sheet when any error occurs while the printer is in PS3 emulation mode. |
Coloration |
Specify the printing methods from Color, Mono, or True Color. |
Image Protect |
Select whether to compress data when memory is low during printing. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Emulation |
Select LJ4. |
Font Source |
Select the default font source. |
Font Number |
Type the default font number from the default font source. |
Pitch |
Type the default font pitch if the font is scalable and fixed-pitch. |
Height |
Type the default font height if the font is scalable and proportional. |
Symbol Set |
Select the default symbol set. |
Form |
Type the number of lines for the selected paper size and orientation. |
Source Symbol Set |
Available only when an optional font ROM is installed. |
Dest Symbol Set |
Available only when an optional font ROM is installed. |
CR Function |
Select CR (carriage-return) or CR+LF (carriage-return/line-feed) operation whenever the print position exceeds the right margin. |
LF Function |
Select LF (line-feed) or CR+LF (carriage-return/line-feed) operation to add a line feed to each carriage return it receives. |
Tray Assign |
Select the tray assigning from 4, 4K, or 5S. When 4, 4K, and 5S are selected, LaserJet 4 Compatible, LaserJet 4000/5000/8000 Compatible, and LaserJet 5 Si Compatible are available respectively. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Emulation |
Select GL2. |
GL-Mode |
Select whether the emulation is similar to the GL/2 or the HP LaserJet 4 emulation of the GL/2. |
Scale |
Select whether the output from the software is scaled, and if so, how the scale factor is calculated: based on the output paper size of the software application. |
Origin |
Select whether the logical origin of the "plotter" is from the corner or the center of the paper. |
Pen |
Select the logical "pen" which "plots" the drawing. |
End |
Select the way in which lines end. |
Join |
Select the way in which lines are joined. |
Pen (0 to 6) |
Select the thickness of the seven "pens" used to make the printout. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Emulation |
Select ESCP2 or FX. |
Font |
Select a font which is used for printing. |
Pitch |
Select a character pitch. |
Condensed |
Use this option to change the character spacing. |
T. Margin |
Use this option to specify the distance from the top of the sheet to the baseline of the first printable line. |
Text |
Use this option to set the page length in lines. |
CG Table |
Use the character generator table option to select the graphics character table, or the italics table. |
Country |
Use this option to select one of the international symbol sets. |
Auto CR |
Use the automatic carriage return option to perform a carriage-return line-feed (CR-LF) operation whenever the print position exceeds the right margin. |
Auto LF |
When you set AutoLF to Off, the printer does not send an automatic line feed (LF) command with each carriage return (CR). When on, the printer adds a line feed to each carriage return it receives. |
Bit Image |
With Bit Image set to Dark or Light, your printer can correctly emulate the graphics densities set with the printer command. When you select Dark, the bit image density is high. When you select Light, the bit image density is low. |
Zero Char |
Select whether the printer prints a slashed zero or an unslashed zero. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Emulation |
Select 1239X. |
Font |
Select a font. |
Pitch |
Select a character pitch. |
Code Page |
Selects the character tables. Character tables contain the characters and symbols used in different languages. |
T. Margin |
Use this option to specify the distance from the top of the sheet to the baseline of the first printable line. |
Text |
Use this option to set the page length in lines. |
Auto CR |
Use the automatic carriage return option to perform a carriage-return line-feed (CR-LF) operation whenever the print position exceeds the right margin. |
Auto LF |
When you set AutoLF to Off, the printer does not send an automatic line feed (LF) command with each carriage return (CR). When on, the printer adds a line feed to each carriage return it receives. |
Alt. Graphic |
Turns the Alternate Graphics option on or off. |
Bit Image |
With Bit Image set to Dark or Light, your printer can correctly emulate the graphics densities set with the printer command. When you select Dark, the bit image density is high. When you select Light, the bit image density is low. |
Zero Char |
Select whether the printer prints a slashed zero or an unslashed zero. |
Character Set |
Select character table. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Items |
Explanations |
Parallel I/F |
Allows you to activate or deactivate the parallel interface. |
Speed |
Select the transfer speed. |
Bi-Directional |
Enable or disable bidirectional communication. |
Buffer Size |
Select the amount of memory to be used for receiving and printing data. |
Items |
Explanations |
Network I/F |
Network I/F (print server) is always on. |
Buffer Size |
Select the amount of memory to be used for receiving and printing data. |
Items |
Explanations |
AUX I/F |
Not available unless an optional print server is installed. |
Buffer Size |
Select the amount of memory to be used for receiving and printing data. Available only when an optional print server is installed. |
Items |
Explanations |
USB I/F |
Allows you to activate or deactivate the USB interface. |
USB Speed |
Select the mode, either HS or FS. |
Buffer Size |
Select the amount of memory to be used for receiving and printing data. |
Set button |
Saves any changes. |
Refresh button |
Clears any changes and reloads the previous settings. |
Previous |
Next |
Version NPD0133-03, Copyright © 2003, SEIKO EPSON CORPORATION |