|
|
Troubleshooting
Head cleaning, ink charging, or ink drying is in progress
An error has occurred
Check to see if the Pause light is flashing. If so, the printer is in the process of head cleaning, ink charging or ink drying. During head cleaning and ink charging, "WAIT" is displayed on the LCD panel. During ink drying, "INK DRY nn MIN" is displayed (nn is the number of remaining minutes). Wait until the printer resumes printing.
Many common printer problems can be identified by the LCD messages and lights on your printer's control panel.
If your printer stops working, use the table below to diagnose the problem, then follow the recommended corrective measures. For other messages not included in the table, see Status messages.
Message and Light |
Problem |
Solution |
PAPER OUT Paper Out |
No paper is loaded in the printer. |
Load paper in the printer. |
Paper ran out. |
Remove any printouts or paper remaining in the printer. Load more paper. |
|
LOAD ROLL PAPER LOAD SHEET PAPER Paper Out |
The paper source setting in the printer driver is different from the control panel. |
Make sure the paper source setting in the printer driver is the same as the control panel. |
PAPER JAM Paper Out |
Paper is jammed in the printer. |
Remove the jammed paper. See also Paper Feed or Paper Jam Problems Occur Frequently. |
COVER OPEN |
Lower cover is open. |
Close the lower cover. |
PAPER NOT CUT Paper Out |
Roll paper was not cut. |
Cut the paper manually, then remove the cut paper from the printer. When RELOAD PAPER is displayed, load paper. |
Cut paper did not fall off. |
Remove the cut paper from the printer. When RELOAD PAPER is displayed, load paper. |
|
PAPER NOT STRAIGHT Paper Out |
Slippage occurred and paper was fed at an angle. |
Reload paper. See Paper Feed or Paper Jam Problems Occur Frequently. |
RELOAD PAPER Paper Out |
Paper could not be reversed into the printing position. |
Remove then reload the paper so that the right and bottom edges are straight and in line with the rows of punch holes on the printer. See "Paper Handling". |
Paper is set out of the printable area. |
||
Paper is set out of the horizontal cutting area. |
||
Paper is not fully ejected. |
Cut the paper at the paper insertion slot, then reload paper. |
|
PAPER NOT CUT error was cleared. |
Reload paper. |
|
PUSH LEVER DOWN Paper Out |
Paper set lever was released during the printing process or another operation. |
Push the paper set lever down. Start printing again from the beginning for best results. |
REMOVE PAPER Paper Out |
Paper set is too thick for head cleaning. |
Push the paper set lever down to remove the paper. Head cleaning automatically starts. After cleaning, when "PAPER OUT" is displayed, reload paper. |
UNABLE TO PRINT |
While an error occurs, or the ink compartment cover is open, you try to print a test pattern (nozzle check, status check, head alignment, or paper thickness pattern) from the SelecType settings. |
After 3 seconds the message disappears. Press the Pause button to exit the SelecType mode. When an error or status message appears again, clear and perform printing a test pattern again. |
INK OUT Y/LM/M/LC/C/K |
Ink cartridge(s) is (are) empty. |
Replace the ink cartridge(s) as indicated by the lights. See Replacing Ink Cartridges. |
NO INK CARTRIDGE Y/LM/M/LC/C/K |
Ink cartridge(s) is (are) not installed. |
Install ink cartridge(s) as indicated by the lights. See Replacing Ink Cartridges. |
WRONG CARTRIDGE Y/LM/M/LC/C/K |
Wrong ink cartridge(s) is (are) installed. |
Use the correct ink cartridge(s). |
OPTION I/F ERROR |
Wrong I/F card is installed. |
Install the correct I/F card after turning off the power. |
SERVICE REQ.nnnnnnnn All lights Flashing |
A fatal error has occurred. |
Note the error number "nnnnnnnn" and contact your dealer. See Contacting Customer Support. |
Next |
Version 1.00E, Copyright © 2001, SEIKO EPSON CORPORATION |