|
|
The Control Panel
Buttons
Lights
Status messages
The control panel of the printer consists of 8 buttons, 12 lights, and a 20-character liquid crystal display (LCD). The control panel layout is shown below.
Power |
Turns the printer on and off. Turn off the printer, then press this button while pressing and holding the Pause button to enter the maintenance mode. See Maintenance Mode. |
Cleaning |
Print head cleaning is performed when pressed for 3 seconds. Before cleaning, make sure that thick paper is not loaded in the printer. |
Pause |
Stops printing temporarily. Press a second time to resume printing. Clears print data in the printer memory if pressed and held for 3 seconds. When pressed in SelecType mode, the printer returns to READY status. |
SelecType |
Enters SelecType mode when pressed in READY status. When pressed in SelecType mode, a desired menu can be selected. |
Paper Source |
Selects the paper source: Roll Auto Cut, Roll Cutter Off or Sheet. When pressed in SelecType mode, a desired item can be selected from the menu. |
Paper Feed (+) |
Feeds paper in reverse. When pressed in SelecType mode, a desired parameter can be selected from the selected item. Parameters change in forward order. |
Paper Feed (-) |
Feeds paper forward. When pressed in SelecType mode, a desired parameter can be selected from the selected item. Parameters change in reverse order. |
Cut/Eject |
When the Sheet light is on:
When the Roll Auto Cut light is on:
When the Roll Cutter Off light is on:
When the Roll Cutter Off light is on and the Print Page Line is on:
Note: When pressed in SelecType mode, it sets the selected parameter in the selected item as the default value. If the selected item is for execution only, the item will be executed. |
|
|
= On |
|
|
= Flashing |
|
= Off |
Operate |
The printer is on. |
Operate |
The printer is receiving print data or shutting down. |
Operate |
The printer is off. |
Paper Out |
The paper is out, the paper set lever is released, or the loaded paper is too thick for head cleaning. |
Paper Out |
The paper is jammed, or another paper output error has occurred. See Printer Stops Printing Unexpectedly. |
Pause |
The printer is ready to print data. |
Pause |
The printer mechanism is moving in preparation for printing, the printed paper is drying for a set time, or the head is being cleaned. |
Pause |
The printer is in pause mode or in SelecType mode, or an error has occurred. See Printer Stops Printing Unexpectedly. |
Ink Out K |
The black ink is out or the black ink cartridge is not installed correctly. |
Ink Out K |
The black ink is low. The black ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Ink Out C |
The cyan ink is out or the cyan ink cartridge is not installed correctly. |
Ink Out C |
The cyan ink is low. The cyan ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Ink Out M |
The magenta ink is out or the magenta ink cartridge is not installed correctly. |
Ink Out M |
The magenta ink is low. The magenta ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Ink Out LC |
The light cyan ink is out or the light cyan ink cartridge is not installed correctly. |
Ink Out LC |
The light cyan ink is low. The light cyan ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Ink Out LM |
The light magenta ink is out or the light magenta ink cartridge is not installed correctly. |
Ink Out LM |
The light magenta ink is low. The light magenta ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Ink Out Y |
The yellow ink is out or the yellow ink cartridge is not installed correctly. |
Ink Out Y |
The yellow ink is low. The yellow ink cartridge is nearly empty. Obtain a replacement ink cartridge. |
Roll |
Auto Cut is selected. The roll paper will be automatically cut after printing. |
Roll |
Roll paper is selected in the printer driver, but Sheet is selected at the control panel. |
Roll |
Printing occurs continuously without cutting. |
Roll |
Roll paper is selected in the printer driver, but Sheet is selected at the control panel. |
Sheet |
Sheet is selected. Printing is on single sheet paper. The printer ejects the paper. |
Sheet |
Sheet is selected in the printer driver, but Roll Auto Cut or Roll Cutter Off is selected at the control panel. |
All lights On |
Reset has been executed by pressing the Pause button for 3 seconds or more. |
The following messages show the printer status. For error messages, see Printer Stops Printing Unexpectedly.
READY |
W* |
Ready to print data. |
POWER OFF |
The power is off. |
|
INK DRY NN MIN |
W* |
Drying ink after printing. Wait for "NN" minutes. |
RESET |
The printer is being reset. |
|
PRESS PAUSE BUTTON |
The Pause button should be pressed. |
|
PRINTING |
W* |
Receiving print data. |
WAIT |
W* |
The printer is warming up, charging ink, or initializing. |
PAUSE |
The printer is paused. To resume printing, press the Pause button. |
|
NO INK CARTRIDGE |
You are replacing the ink cartridge(s). |
|
INK LOW |
Ink cartridge(s) is (are) nearly empty. Replace the ink cartridge(s) indicated by the Ink Out light(s). When the ink cartridge(s) is (are) out, printing stops. Printing can be resumed after empty cartridge(s) have been replaced. |
|
LOAD PAPER |
The paper set lever is down while loading paper. When you load paper and pull the set lever up, "PRESS PAUSE BUTTON" appears. |
|
TURN PWR OFF AND ON |
After clearing jammed paper, this message appears. Turn the printer off and on. |
|
INK CHARGING nnn% |
The printer is charging the ink delivery system. This message shows the progress of the ink charging process. |
|
TRANSPORT PREP nn% |
The printer is preparing for transportation. This message shows the progress of the preparation process. |
|
MAINTENANCE REQ. nnnn |
A part used in the printer has nearly reached the end of its service life. Note the error number "nnnn" and contact your dealer. See Contacting Customer Support. |
* Indicates the Platen Gap setting is set to WIDE. When AUTO is selected, no letter appears. |
Next |
Version 1.00E, Copyright © 2001, SEIKO EPSON CORPORATION |