Safety Instructions

Read all of the instructions in this section before using your printer. Also, be sure to follow all warnings and instructions marked on the printer.

When setting up your printer

Observe the following when setting up the printer:

• Do not block or cover the vents and openings in the printer.

• Power supply cords should be placed to avoid abrasions, cuts, fraying, crimping, and kinking. Do not place objects on top of power-supply cords and do not allow the AC adapter or power-supply cords to be stepped on or run over. Be particularly careful to keep all power-supply cords straight at the ends and the points where they enter and leave the AC adapter.

• Use only the the power-supply cords A361H that comes with this product. Use of another cord may result in fire or electrical shock, or injury.

• The AC adapter model A361H is designed for use with the printer with which it was included. Do not attempt to use it with other electronic devices unless specified.

• Use only the type of power source indicated on the AC adapter's label, and always supply power directly from a standard domestic electrical outlet with the AC power cord that meets the relevant local safety standards.

• Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off.

• Avoid using electrical outlets controlled by wall switches or automatic timers.

• Keep the entire computer system away from potential sources of electromagnetic interference, such as loudspeakers or the base units of cordless telephones.

• Do not use a damaged or frayed power cord, AC adapter, and the optional battery.

• If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed the cord's ampere rating. Also, make sure that the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet's ampere rating.

• Never disassemble, modify, or attempt to repair the AC adapter, power cord, printer, and options by yourself except as specifically explained in the printer's guides.

• Unplug the printer and the AC adapter, remove the optional battery from the printer, and refer servicing to qualified service personnel under the following conditions:

The power cord or plug is damaged; liquid has entered the printer, the AC adapter, or the optional battery; the printer, the AC adapter or the optional battery has been dropped or the casing damaged; the printer, the AC adapter or the optional battery does not operate normally or exhibits a distinct change in performance. (Do not adjust controls that are not covered by the operating instructions.)

• Do not use with wet hands.

• If you plan to use the AC adapter or the optional battery in Germany, the building installation must be protected by a10 or 16 amp circuit breaker to provide adequate short-circuit protection and over-current protection for this printer.

For United Kingdom, Singapore, and Hong Kong users

• Replace fuses only with fuses of the correct size and rating.

Safety Requirements

Mains plug:
Use a 3-pin mains plug that is registered with the Safety Authority.

Flexible cord:
Use a double insulated flexible cord that is certified* to the relevant IEC or BS standards.

Appliance connector:
Use an appliance connector certified* to the relevant IEC or BS Standards.

*  certified by member of IECEE CB Scheme.

For United Kingdom users

The following safety information applies to the AC adapter.

• Warning: Refer to the rating plate for the voltage and check that the appliance voltage corresponds to the supply voltage.

• Important: The wires in the mains lead fitted to this appliance are coloured in accordance with following code: Blue - Neutral, Brown - Live

If you have to fit a plug:

• As the colours of the mains lead of the appliance may not match the coloured markings used to identify the terminals in a plug, please observe the following:

• The blue wire must be connected to the terminal in the plug marked with the letter N.

• The brown wire must be connected to the terminal in the plug marked with the letter L.

• If damage occurs to the plug, replace the cord set or consult a qualified electrician.

When choosing a place for the printer

Observe the following when choosing a place for the printer:

• Place the printer on a flat, stable surface that extends beyond the base of the printer in all directions. If you place the printer by the wall, leave more than 10 cm between the back of the printer and the wall. The printer will not operate properly if it is tilted at an angle.

• When storing or transporting the printer, do not tilt it, stand it on its side, or turn it upside down. Otherwise, ink may leak from the cartridge.

• Leave enough space in front of the printer for the paper to be fully ejected.

• Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer and the AC adapter away from direct sunlight, strong light, water, or heat sources.

• Avoid places subject to dust, shock, or vibration.

• Leave enough room around the printer to allow for sufficient ventilation.

• Place the AC adapter near a wall outlet where the plug can be easily unplugged.

• Do not place or store the printer, the AC adapter, or the optional battery outdoors.

When using the printer

Observe the following when using the printer:

• If you use the printer in places where the use of electronic devices is limited, such as in airplanes or hospitals, follow all instructions in those places.

• Do not insert objects through the slots in the printer.

• Take care not to spill liquid on the printer and the AC adapter.

• Do not put your hand inside the printer or touch the photo cartridge during printing.

• Always turn the printer off using the On button. Do not unplug the printer or turn off the power to the outlet until the power light goes out.

• Before transporting the printer, make sure that the photo cartridge is in place.

• Leave the photo cartridge installed. Removing the cartridge can dehydrate the print head and may prevent the printer from printing.

When using the optional battery

• If battery acid gets into your eyes or on your skin, immediately rinse the affected area thoroughly with water and seek medical treatment. If a battery is swallowed, seek medical treatment immediately.

• Use only an Epson Li-ion battery model EU-112 for this printer according to the directions in the user documentation. Replacing the battery with an incorrect model may cause an explosion.

• Use only AC adapter model A361H to charge the battery and operate the printer.

• Do not charge or use the battery with devices other than the specified product. Using the battery with other devices may damage the battery or other devices, or may cause an explosion.

• To protect against short-circuiting, do not remove the outside case of the battery.

• Do not handle the battery with wet hands or use them near water.

• Do not expose the battery to water or high humidity.

• Do not drop, puncture, disassemble, mutilate, or short-circuit the battery.

• Do not place the battery near or into fire or water.

• Do not use the battery that is leaking or damaged in any way.

• Do not charge the battery on devices except this product.

• Do not charge the battery near open flame or in very hot locations.

• Keep the battery away from heat sources.

• Do not leave the battery in a vehicle to prevent the battery from overheating.

• Do not insert objects into any openings as they may touch dangerous voltage points or short-circuit components.

• Prevent the battery from coming into contact with metal objects that could short-circuit it, such as coins or keys.

• Do not solder wires or terminals directly to the battery.

• Do not touch battery terminals.

• Keep the battery away from open flame if they leak or smell strange.

• If overheating, discoloration, or deformation occur, remove the battery from this product and do not use it.

• Charge the battery before using it if it has not been used for a long period.

When storing the optional battery

• When not using the printer for a long period of time, remove the battery from the printer and store them separately to avoid over-discharging the battery.

• Do not store the battery where the temperature or humidity is very high.

• Store the battery out of children's reach.

When disposing of the optional battery

Before disposing of the battery, make sure you discharge them completely.

Warning:

Do not dispose of batteries as ordinary refuse. Instead, dispose of them in a collection or recycle box in accordance with local laws.

Do not incinerate or dispose of the battery in fire.

For European users:

Do not dispose of batteries as ordinary refuse. Instead, dispose of them in a recycle box in accordance with local laws.

For users in the United States and Canada:

When handling photo cartridges

Observe the following when handling photo cartridges:

• Keep photo cartridges out of the reach of children. Do not allow children to drink from or otherwise handle the cartridges.

• Do not shake photo cartridge after removing it from the bag; this can cause leakage.

• Be careful when you handle used photo cartridges, as there may be some ink remaining around the ink supply ports. If ink gets onto your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. If discomfort or vision problems continue after a thorough flushing, see a doctor immediately.

• Do not remove or tear the label on the cartridge; this can cause leakage.

• Install the photo cartridge immediately after you remove it from its package. If you leave a cartridge unpacked for a long time before using it, normal printing may not be possible.

• Do not use a photo cartridge beyond the date printed on the cartridge carton: otherwise, it may result in reduced print quality. For best results, use up the photo cartridge within six months of installing it.

• Do not dismantle photo cartridges or try to refill them. This could damage the print head.

• After bringing a photo cartridge inside from a cold storage site, allow it to warm up at room temperature for at least three hours before using it.

• Store photo cartridges in a cool, dark place.

• Do not touch the green IC chip on the bottom of the cartridge. Doing so may prevent normal operation and printing.

• The IC chip on the photo cartridge retains a variety of cartridge-related information, such as the amount of ink remaining, so that the cartridge may be removed and reinstalled freely. However, each time the cartridge is inserted, some ink is consumed because the printer automatically performs a reliability check.

• If you remove the photo cartridge for later use, protect the ink supply ports from dirt and dust and store it in the same environment as the printer. A valve in the ink supply ports makes covers or plugs unnecessary, but the ink may stain items that come into contact with this area of the cartridge. Do not touch the ink supply ports or the surrounding area.

• Store each photo cartridge so that the bottom of its packaging faces down.

ENERGY STAR^® Compliance

As an ENERGY STAR^® Partner, Epson has determined that this product meets the ENERGY STAR^® guidelines for energy efficiency.

The International ENERGY STAR^® Office Equipment Program is a voluntary partnership with the computer and office equipment industry to promote the introduction of energy-efficient personal computers, monitors, printers, fax machines, copiers, scanners, and multifunction devices in an effort to reduce air pollution caused by power generation. Their standards and logos are uniform among participating nations.

Warnings, Cautions, and Notes

Warnings

must be followed carefully to avoid bodily injury.

Cautions

must be observed to avoid damage to your equipment.

Notes

contain important information and useful tips on the operation of your printer.