Important Safety Instructions

Do not block or cover the vents and openings in the product.

Use only the type of power source indicated on the product’s label.

Use only the power cord that comes with the product. Use of another cord may result in fire or electric shock.

The product’s power cord is for use with the product only. Use with other equipment may result in fire or electric shock.

Be sure your AC power cord meets the relevant local safety standard.

Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off.

Avoid electrical outlets controlled by wall switches or automatic timers.

Keep the entire computer system away from potential sources of electromagnetic interference, such as loudspeakers or the base units of cordless telephones.

The power-supply cords should be placed to avoid abrasions, cuts, fraying, crimping, and kinking. Do not place objects on top of the power-supply cords and do not allow the power-supply cords to be stepped on or run over. Be particularly careful to keep all the power-supply cords straight at the ends and the points where they enter and leave the transformer.

If you use an extension cord with the product, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating. Also, make sure that the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating.

Never disassemble, modify, or attempt to repair the power cord, printer unit, scanner unit, or options by yourself, except as specifically explained in the product’s guides.

Unplug the product and refer servicing to qualified service personnel under the following conditions:
The power cord or plug is damaged; liquid has entered the product; the product has been dropped or the casing damaged; the product does not operate normally or exhibits a distinct change in performance. Do not adjust controls that are not covered by the operating instructions.

If you plan to use the product in Germany, the building installation must be protected by a 10 or 16 amp circuit breaker to provide adequate short-circuit protection and over-current protection for the product.

When connecting the product to a computer or other device with a cable, ensure the correct orientation of the connectors. Each connector has only one correct orientation. Inserting a connector in the wrong orientation may damage both devices connected by the cable.

If damage occurs to the plug, replace the cord set or consult a qualified electrician. If there are fuses in the plug, make sure you replace them with fuses of the correct size and rating.

Place the product on a flat, stable surface that extends beyond the base of the product in all directions. If you place the product by the wall, leave more than 10 cm between the back of the product and the wall. The product will not operate properly if it is tilted at an angle.

When storing or transporting the product, avoid tilting it, placing it vertically, or turning it upside down; otherwise ink may leak.

Allow spaces behind the product for the cables, and space above the product so that you can fully raise the document cover.

Avoid places subject to rapid changes in temperature and humidity. Also, keep the product away from direct sunlight, strong light, or heat sources.

Do not place or store the product outdoors, near excessive dirt or dust, water, heat sources, or in locations subject to shocks, vibrations, high temperature or humidity. Do not use with wet hands.

Place the product near a wall outlet where the plug can be easily unplugged.

Do not insert objects through the slots in the product.

Take care not to spill liquid on the product.

Do not put your hand inside the product or touch the ink cartridges during printing.

Do not touch the white flat cable inside the product.

Do not use aerosol products that contain flammable gases inside or around the product. Doing so may cause fire.

Do not move the print head by hand; otherwise, you may damage the product.

Always turn the product off using  button. When this button is pressed, the  light flashes. Do not unplug the product or turn off the power to the outlet until the  light stops flashing.

Before transporting the product, make sure that the print head is in the home (far right) position and the ink cartridges are in place.

Be careful not to trap your fingers when closing the scanner unit.

If you are not going to use the product for a long period, be sure to unplug the power cord from the electrical outlet.

Do not press too hard on the document glass when placing the originals.

Bank bills, coins, government-issued marketable securities, government bond securities, and municipal securities

Unused postage stamps, pre-stamped postcards, and other official postal items bearing valid postage

Government-issued revenue stamps, and securities issued according to legal procedure

Private marketable securities (stock certificates, negotiable notes, checks, etc.), monthly passes, concession tickets, etc.

Passports, driver’s licenses, warrants of fitness, road passes, food stamps, tickets, etc.

Products can be misused by improperly copying copyrighted materials. Unless acting on the advice of a knowledgeable attorney, be responsible and respectful by obtaining the permission of the copyright holder before copying published material.