Home
Setting an IP Address on the Printer’s Control Panel

Network Menu
AUX Menu

After connecting the printer to the network, you need to set the IP address for the network interface.

To set the IP address, subnet mask, and default gateway from the control panel, follow the steps below.

Turn on your printer.

Press the Enter button on the printer's control panel once to enter the SelecType mode. The LCD panel displays Information Menu.

Press the Up or Down button until Network Menu appears. Then press the Enter button.

Check that Network I/F = On appears.

    If Network I/F = Off appears instead, press the Enter button and then the Up or Down button to change to Network I/F = On. Then press the Enter button, turn off the printer for more than five seconds, and turn it back on.

Press the Up or Down button until Get IP Address = Auto appears. Press the Enter button and then the Up or Down button to change to Get IP Address = Panel. Then press the Enter button. You can use the following methods to get an IP address.

  • Choose Panel when setting the IP address, subnet mask, and default gateway using the printer’s control panel.

  • Choose Auto when getting the IP address from a DHCP server. The IP address is automatically obtained from the DHCP server whenever the printer is reset or turned on.

  • Choose PING when setting the IP address using the arp/ping command. The network interface uses the IP address set by the arp/ping command. The settings become available when the printer is reset or turned off and then back on.


Note:
  • To use Auto, a DHCP server must be correctly configured on the network. See the online help of your operating system for detailed instructions.

  • Choose PING only when setting the IP address using the arp/ping command.

Press the Up or Down button until IP = xxx.xxx.xxx.xxx appears. Press the Enter button.

Press the Up or Down button until the desired value appears. Then press the Enter button to set the value.


Note:

Repeat steps 7 and 8 to set the IP address, subnet mask, and default gateway.

Press the Start button to exit the control panel menus.

Turn off your printer and then turn it back on. Be sure to wait until the initialization is complete.

Print a network status sheet to confirm the new IP address.


Note:
  • You must first set the IP address before using EpsonNet Config with Web Browser.

  • See the User's Guide for more information about settings on the printer’s control panel.

Network Menu

These items are used to make network settings on the printer’s control panel.

Item

Settings (default in bold)

Network I/F

On, Off

Get IPAddress

Panel, Auto, PING

IP

0.0.0.0 to 255.255.255.255

SM

0.0.0.0 to 255.255.255.255

GW

0.0.0.0 to 255.255.255.255

NetWare

On, Off

AppleTalk

On, Off

MS Network

On, Off

Bonjour

On, Off

Link Speed

Auto, 100 Full, 100 Half, 10 Full, 10 Half

Buffer Size

Normal, Maximum, Minimum


Note:
  • To activate the Network Menu settings, you must turn off the printer for more than five seconds and then turn it back on. Or, you can perform a Reset All operation, as explained in “Reset Menu” in the User's Guide.

  • Resetting the printer erases all print jobs. Make sure the Ready light is not flashing when you reset the printer.

Top
AUX Menu

This menu allows you to control the optional interface settings from the printer’s control panel.


Note:

The AUX Menu appears only when an optional interface is installed.

Item

Settings (default in bold)

AUX I/F

On, Off

Get IPAddress*

Panel, Auto, PING

IP*

0.0.0.0 to 255.255.255.255

SM*

0.0.0.0 to 255.255.255.255

GW*

0.0.0.0 to 255.255.255.255

NetWare*

On, Off

AppleTalk*

On, Off

MS Network*

On, Off

Bonjour*

On, Off

AUX Init*

-

Buffer Size*

Normal, Maximum, Minimum

* Available only when On is selected as the AUX I/F setting.

AUX I/F

Allows you to activate or deactivate the AUX interface when an optional interface card is installed.

Buffer Size

Determines the amount of memory to be used for receiving data and printing data. If Maximum is selected, more memory is allocated for receiving data. If Minimum is selected, more memory is allocated for printing data.


Note:
  • To activate Buffer Size settings, you must turn off the printer for more than five seconds then turn it back on. Or, you can perform a Reset All operation, as explained in “Reset Menu” in the User's Guide.

  • Resetting the printer erases all print jobs. Make sure the Ready light is not flashing when you reset the printer.

Top